PIX TO ASA MIGRATION TOOL 8.4 PASSWORD 8RY2YJIYT7RRXU24 ENCRYPTED

Pix To Asa Migration Tool 8.4 Password 8Ry2YjIyt7RRXU24 Encrypted

Enable password 8Ry2YjIyt7RRXU24 encrypted. Migrate from ASA 5510/5520 IOS software to.ASA Version 8.4(2) hostname ciscoasa. Configure IKEv1 IPsec Site-to-Site Tunnelswith the ASDM or CLI on the ASA ContentsRequires upgrading Cisco ASA 5510/5520 firewall running IOS code 8.2 and 8.3 to 8.4 code then to 9.8 version. If you have a service.1 answer Top answer: Option 1 - manual conversionCiscos Migration Guide for Converting Cisco PIX Configurations to Cisco ASA 5500 Series Configurations has a whole. Option 3 : convert using the conversion tool. X config, then upgrade it back to the desired version (in steps, if needed).

If you configure the peer IP address on Site A, it must be changed to 172.16.1.1. In this example, the peer IP address is set to 192.168.1.1 onSite B. If your network islive, make sure that you understand the potential impact of any command.This section describes how to configure the site-to-site VPN tunnel via the Adaptive SecurityDevice Manager (ASDM) VPN wizard or via the CLI.This is the topology that is used for the examples throughout this document:Complete these steps in order to set up the site-to-site VPN tunnel via the ASDM wizard:Open the ASDM and navigate to Wizards > VPN Wizards > Site-to-site VPN Wizard:1.Click Next once you reach the wizard home page:Note: The most recent ASDM versions provide a link to a video that explains thisconfiguration.Configure the peer IP address. All ofthe devices used in this document started with a cleared (default) configuration. This document describes how to configure an Internet Key Exchange version 1 (IKEv1) IPsec site-to-site tunnel between a Cisco 5515-X Series Adaptive Security Appliance (ASA) that runssoftware Version 9.2.x and a Cisco 5510 Series ASA that runs software Version 8.2.x.Cisco recommends that these requirements be met before you attempt the configuration that isdescribed in this document:The end-to-end IP connectivity must be established.User Datagram Protocol (UDP) 5 for the IPsec control planeEncapsulating Security Payload (ESP) IP Protocol 50 for the IPsec data planeThe information in this document is based on these software and hardware versions:Cisco 5510 Series ASA that runs software Version 8.2Cisco 5515-X ASA that runs the software Version 9.2The information in this document was created from the devices in a specific lab environment. Enterprise Networking Routers, Switches, Firewalls and other Data Networking infrastructure discussions welcomed.

This is the NAT rule that isused:Note: When multiple subnets are used, you must create object groups with all of the sourceand destination subnets and use them in the NAT rule.Here is the complete configuration for Site B:Tunnel-group 192.168.1.1 ipsec-attributes!Note the IKEv1 keyword at the beginning of the pre-shared-key command.Access-list 100 extended permit ip object 10.2.2.0_24 object 10.1.1.0_24Crypto ipsec ikev1 transform-set myset esp-aes esp-sha-hmacCrypto map outside_map 20 match address 100Crypto map outside_map 20 set peer 192.168.1.1Crypto map outside_map 20 set ikev1 transform-set mysetNat (inside,outside) 1 source static 10.2.2.0_24 10.2.2.0_24 destination static10.1.1.0_24 10.1.1.0_24 no-proxy-arp route-lookupConfigure Site A for ASA Versions 8.2 and EarlierThis section describes how to configure Site A for ASA Versions 8.2 and earlier.Enter this command into the CLI in order to enable Internet Security Association and KeyManagement Protocol (ISAKMP) on the outside interface:Note: Because multiple versions of IKE (IKEv1 and IKEv2) are not supported any longer, theISAKMP is used in order to refer to Phase 1.Create an ISAKMP policy that defines the algorithms/methods to be used in order to buildPhase 1. An identical TSmust be created on the remote end as well.Configure the crypto map, which contains these components:The defined access list that contains the traffic of interestAn optional Perfect Forward Secrecy (PFS) setting, which creates a new pair of Diffie-Hellman keys that are used in order to protect the data (both sides must be PFS-enabledbefore Phase 2 comes up)Apply the crypto map on the outside interface:Ensure that the VPN traffic is not subjected to any other NAT rule. Create two objects thathave the local and remote subnets and use them for both the crypto Access Control List(ACL) and the NAT statements.Configure the Transform Set (TS), which must involve the keyword IKEv1. It can contain multiple entries if there are multiple subnets involved between thesites.In Versions 8.4 and later, objects or object groups can be created that serve as containersfor the networks, subnets, host IP addresses, or multiple objects. In this example,the traffic of interest is the traffic from the tunnel that is sourced from the 10.2.2.0 subnet tothe 10.1.1.0. Note: For the example that is used in thisdocument, inside is the source of thetraffic.The wizard now provides a summary of the configuration that will be pushed to the ASA.Review and verify the configuration settings, and then click Finish.This section describes how to configure the IKEv1 IPsec site-to-site tunnel via the CLI.Configure Site B for ASA Versions 8.4 and LaterIn ASA Versions 8.4 and later, support for both IKEv1 and Internet Key Exchange version 2(IKEv2) was introduced.Tip: For more information about the differences between the two versions, refer to the Whymigrate to IKEv2? section of the Swift Migration of IKEv1 to IKEv2 L2L Tunnel Configurationon ASA 8.4 Code Cisco document.Tip: For an IKEv2 configuration example with the ASA, refer to the Site-to-Site IKEv2 Tunnelbetween ASA and Router Configuration Examples Cisco document.Complete these steps for the Phase 1 configuration:Enter this command into the CLI in order to enable IKEv1 on the outside interface:Create an IKEv1 policy that defines the algorithms/methods to be used for hashing,authentication, Diffie-Hellman group, lifetime, and encryption:Create a tunnel group under the IPsec attributes and configure the peer IP address and the3.Complete these steps for the Phase 2 configuration:Create an access list that defines the traffic to be encrypted and tunneled.